DIY Projects to Illuminate Your Home

Do you want to enhance the overall appearance of your Home? 

Do you like the idea of using everyday stuff for decor? 

Do you need budget-friendly home improvements? 

In simple, do you want to upgrade your home without worrying about budget and effort?

We are here to guide you in this journey. We have mentioned some projects that you can do yourself to make your home look better.

Wall Lamps

The first thing you can do to make your home appealing is to change the home lighting. Installing wall lamps can prove vital in this aspect. These lamps not only provide ambiance but also add a touch of elegance to your home. 

If you are looking to install wall lamps, here is a quick guide for you:

Required Materials

The materials that you’ll need are mentioned below:

  • Wall Lamp fixture
  • Screwdriver
  • Electrical Tape
  • Wire Stripper
  • Voltage tester
  • Light bulb
  • Pencil

Steps

By using the tools and following these steps, you can easily add a wall lamp in no time.

  • Determine the location where you want to install the lamp. 
  • Ensure the location is near a power source. Also, consider the height parameters. 
  • It is compulsory to turn off the power before starting any electrical work.
  • This is for the safety of you while you are working with electrical components. 
  • To get an idea, hold the lamp base against the wall in the desired location. Use a pencil to mark the spots where the screws will go.
  • Make sure that the lamp is level. 
  • If your wall lamp comes with a mounting bracket, attach it to the wall using the screws and anchors provided.
  • Make sure the bracket is secure.
  • Now comes the time to connect the wires. Gently pull the wires from the lamp through the bracket. 
  •  If your lamp has wires exposed, use electrical tape to insulate the ends. 
  • If the wires are connected to a junction box, follow the manufacturer’s instructions for wiring.
  • Hold the lamp against the bracket, aligning the holes on the lamp base with the screws on the bracket. 
  • Secure the lamp in place by tightening the screws.
  • If your lamp didn’t come with a bulb pre-installed, screw in the appropriate light bulb.
  • Make sure not to overtighten it. Look out for the Strak LED collection which is long-lasting and durable.
  • Before finishing up, turn the power back on and use a voltage tester to ensure there’s electricity flowing to the lamp. 
  • If everything is working, turn off the power again.
  • If your lamp allows for adjustments, set it to the desired angle. Double-check that all connections are secure. 
  • Finally, turn the power back on and enjoy your newly installed wall lamp.
You can look out for a Chinese copper crystal lotus wall lamp, Nordic Minimalist Swing Adjustable Arm Industrial Wall Lamp, and Nordic Modern Wall Lamp Bedside Bedroom Living Room LED wall Light Sconces at Strak LED. Strak LED also offers numerous lighting products that can make your wall lamp illuminate with a brilliant glow. 

Ceiling lights

Ceiling lights are an essential necessity for lighting for homes. But, we at Strak LED believe that it is more than just a fixture. If you use modern and uniquely designed ceiling lights, they can add a touch of elegance and warmth to your home. 

If you are ready to upgrade your house lights, here is a comprehensive guide on installing the ceiling light fixture yourself. 

Required Materials

  • Ceiling light fixture
  • Wire nuts
  • Screws
  • Screwdriver
  • Voltage tester
  • Wire stripper
  • Wire cutter
  • Ladder or step stool

Steps

Are you looking to upgrade your home lighting by changing the ceiling lights? Follow the steps given below for better understanding:

  • Safety should be your first priority. Ensure the power is switched off at the circuit breaker. 
  • Before changing the lighting for home, test the existing light fixture to make sure that there’s no electricity flowing through it. 
  • If there is an existing fixture, remove it by unscrewing the nuts that hold it in place. 
  • Gently disconnect the wires. Be sure to support the fixture as you disconnect it.
  • Examine the wiring in your ceiling to ensure it is compatible with the new lighting fixture. 
  • If you are unable to understand the wiring, it is recommended to consult an expert. 
  • Strip the insulation from the ends of the wires on both the ceiling and the new light fixture. 
  • Twist together the wires of the same colour. Typically, black to black (hot), white to white (neutral) and green to green (ground).
  • Attach the mounting bracket that came with the new fixture to the ceiling junction box using screws. 
  • Ensure it’s stable and properly aligned.
  • Gently lift the new ceiling light fixture and connect the wires from the fixture to the corresponding wires in the ceiling using wire nuts. 
  • Carefully tuck the wires into the junction box.
  • Secure the fixture to the mounting bracket using the screws provided. 
  • Make sure the fixture is level and flush with the ceiling.
  • Insert the appropriate light bulbs into the fixture. 
  • Follow any instructions provided by the manufacturer.
  • Turn the power back on at the circuit breaker.
  • Use a voltage tester to ensure there’s electricity flowing to the fixture.
  • Turn on the light to confirm it’s working properly. 
  • Double-check that the fixture is securely fastened to the ceiling.
If you are looking to change the ceiling lights but are worried about lighting products like bulbs, LEDs, and slim panel downlights. Explore the wide range of Strak LED’s products. We provide a G9 Led collection, G4 Led collection, Pot lights / Downlights, candle bulbs, flush mount fixtures, commercial fixtures, A19 bulbs, and many more. One thing that is common in all these products is that they are reliable, durable, and energy-efficient. 

Pendant Lights

Pendant lights are an elegant home lighting fixture. Most people employ pendant lights when they are changing lighting for homes. It is because they are stylish and versatile home lighting options that can transform the ambiance. 

Pendant lights are the best option for upgrading the house lights. Here is a comprehensive guide for you:

Required Materials 

If you changing house lights, most of the materials required are generally the same:

  • Pendant light fixture
  • Ceiling Canopy
  • Mounting Bracket
  • Wire Nuts
  • Wire Stripper
  • Screwdrivers
  • Voltage Tester
  • Ladder

Steps

Follow the below steps for changing lights for home and installing pendant lights.

  • Before you start, turn off the power to the room from your home’s circuit breaker. 
  • Use a voltage tester to confirm that the power is off.
  • If you are replacing an existing home lighting fixture, carefully remove it.
  • Use a screwdriver to unscrew the nuts that are holding that lighting for home and disconnect the wires.
  • Follow the manufacturer’s instructions to attach the mounting bracket to the ceiling electric box using screws. 
  • Make sure that the bracket is securely fastened and level.
  • Carefully connect the wires from the pendant lights to the corresponding wires from the ceiling using wire nuts.
  • Connect the black wire to black, white wire to white, and green wire to green of the ceiling wires. 
  • Gently lift the canopy to cover the wiring and mounting bracket. Secure the canopy to the mounting bracket using screws.
  • Ensure the canopy is flush against the ceiling. 
  • Now, with the canopy in place, hang the pendant home lighting fixture from the hook provided by the manufacturer.
  • Adjust the height as desired.
  • Give the pendant light a final check to ensure it’s level and secure.
  • Once you’re satisfied, turn the power back on from the circuit breaker and test the light to ensure it’s working correctly.
If you are looking for a house lights option, explore the variety of products at Strak LED. The candle bulbs, G9 LED collection, A19 LED bulbs, and slim panel downlights can surely convert the appearance of your home into an inviting and wonderful appearance. 

Chandeliers

The top-selling and people’s favourite home lighting fixture is the chandeliers. Why it is that popular lighting for homes? Because adding a chandelier to your home can instantly enhance elegance and create a focal point that draws attention. 

Whether you are looking to install a chandelier in your dining room, or living room, here is a complete guide that will assist you in upgrading the house lights. 

Required Materials

The materials that are required for changing this home lighting fixture are as follows:

  • Chandelier
  • Ceiling Mounting Bracket
  • Wire Stripper
  • Electrical Tape
  • Wire Nuts
  • Screwdrivers
  • Ladder
  • Voltage tester

Steps

Here are the easy installation steps for upgrading lighting for your home. Furthermore, you can consult an expert for guidance as well. 

  • The very first step while installing a home lighting fixture is ensuring safety. 
  • Turn off the power to the installation area from the circuit breaker to ensure your safety. 
  • Choose the location where you want to install the chandelier. 
  • Make sure it’s centred and balanced in the room. 
  • Attract the mounting bracket according to the manufacturer’s instructions. 
  • Use a level to ensure that it is straight. 
  • Strip the insulation from the wires of the chandelier and from the wires coming from the ceiling. 
  • Connect the matching wires. The same colour wires should be connected to each other. 
  • Gently lift the chandelier and connect its wires to the wires from the ceiling. 
  • Secure the canopy in place using screws.
  • Now, if you have a chandelier with multiple parts, assemble them according to the manufacturer’s instructions. 
  • Attach any crystals, shades, or decorative elements.
  • Double-check that all wires are properly connected and secured with wire nuts.
  • Use electrical tape to insulate the wire connections.
  • Now, you can turn on the power from the circuit breaker and test if the chandelier is working properly. 
  • Use a voltage tester to confirm that the home lighting fixture is properly installed. 
Commonly, LEDs are used in the chandeliers. Look out for the Strak LED collection that offers brilliant glow, energy efficiency, and durability. 

Conclusion

Upgrading the home lighting can prove vital in improving the elegance and appearance of the home. With the above-mentioned DIY projects, you can change the house lights without much effort. Whether you’re captivated by wall lamps, impressed by ceiling lights, charmed by pendant lights, or taken in by the classic beauty of chandeliers, these fixtures can truly transform your surroundings. Always prioritize safety when you are working with lighting for home. Look out for the strak LED collection to ensure a long-lasting investment. 

FAQs

Are you confused about something? Here are the frequently asked questions and their answers. 

What are the home lighting fixtures I can use to illuminate the home?

You can use wall lamps, ceiling lights, pendant lights, and chandeliers to illuminate your home. Use effective house light products in these fixtures for a bright glow.

How can I ensure the safety of electrical work while installing wall lamps?

Always turn off the power before starting any electrical work, and use a voltage tester to confirm there’s no electricity flowing.

What materials do I need for a DIY ceiling light installation?

Required materials include a ceiling light fixture, wire nuts, screws, screwdriver, voltage tester, wire stripper, wire cutter, and a ladder or step stool.

Where can I find reliable lighting for home products for DIY projects?

Look for lighting for home products at Strak LED, where you can find various options such as LEDs, slim panel downlights, candle bulbs, and collections like G9 LED and A19 LED bulbs that combine reliability, durability, and energy efficiency.

How is a chandelier attached?

Attach the chandelier’s mounting bracket to the ceiling box using screws. Insert the hook located at the chandelier’s end into the bracket. Then, connect the fixture’s mounting stem to the pre-existing bracket on the ceiling box.

soon..

Leave a Reply

Your email address will not be published. Required fields are marked *